Heat seal applications Heat Sealing/ Heat seal application Flex (FPC) to glass (LCD) and Heat seal-/ Heat seal application circuit board (PCB) to flex (FPC) to glass(LCD) more...
Irradiation chamber with 400W or 1000W emitters.
The internal base plate can be inserted into the lateral guides at different heights.
The drawer base is loaded with the products to be irradiated and the door is closed and locked and the irradiation started.
The integral UV emitter is fitted with a shutter.
Only after the door is closed and locked can radiation be emitted following the automatic opening of the shutter system.
Should the door be forcibly opened during irradiation, the UV emitter is automatically switched off.
There is an integral power-monitoring UV sensor and if the measured UV output falls below a set value, an alarm is generated.
The system has a small SPS with a display. The required irradiation time can be set and the time already expired is displayed.
There is also a permanently running operating hours clock and an operating hours clock whic more...
Very robust diaphragm dispensing valve.
Due to its simple design this valve is very easy to handle and simple to maintain.
The membrane is made of Teflon and the through-flow body is made of stainless steel.
The through-flow body is equipped with a heating.
The temperature range can be adapted to customer requirements.
The heating control system monitors and controls the valve set temperature with an accuracy of up to + /-1K.
The valve lift is adjustable and can optionally be monitored by a sensor (dispensing control). more...
Irradiation chamber with 900W emitter.
The drawer is loaded with the products to be irradiated and pushed into the system, where it is automatically locked and the irradiation commenced.
The integral UV lamp is fitted with a shutter and only after the drawer is locked in position can radiation be emitted following the automatic opening of the shutter system.
Should the door be forcibly opened during irradiation, the UV emitter is automatically switched off.
There is an integral power-monitoring UV sensor and if the measured UV output falls below a set value, an alarm is generated.
The system has a small SPS with a display. The required irradiation time can be set and the time already expired is displayed.
There is also a permanently running operating hours clock and an operating hours clock which can be reset.
The irradiation procedure can be stopped if necessary by more...
Drawer/Irradiation chamber with 450W emitters.
The drawer is loaded with the products to be irradiated and pushed into the system, where it is automatically locked and the irradiation commenced.
The integral UV lamp is fitted with a shutter and only after the drawer is locked in position can radiation be emitted following the automatic opening of the shutter system.
Should the door be forcibly opened during irradiation, the UV emitter is automatically switched off.
There is an integral power-monitoring UV sensor and if the measured UV output falls below a set value, an alarm is generated.
The system has a small SPS with a display. The required irradiation time can be set and the time already expired is displayed.
There is also a permanently running operating hours clock and an operating hours clock which can be reset.
The irradiation procedure can be stopped if neces more...
Heating rails for heat sealing systems are supplied in infinitely variable lengths from 5mm to 300mm.
Contact units, which are gold-plated on the edges are fitted to an aluminium base and these provide electrical contacts for the measurement wires of the control electronics and the heater connection wires.
The actual heater elements, the so-called heater strips, are thermally insulated from the base and fixed to the contact units by a âbelt tensioning systemâ.
The heater strips have a low thermal mass, so that they are heated and cooled in the shortest possible time.
At several points on the inside of the heating strips there are additional temperature sensors for collective temperature monitoring.
The heater rails are extremely robust and durable. Replacement, e.g. at product change-over, is achieved with few handgrips.
In complex production plants, the he more...
Heat seal applications Heat Sealing/ Heat seal application Flex (FPC) to glass (LCD) and Heat seal-/ Heat seal application circuit board (PCB) to flex (FPC) to glass(LCD) more...
Multiple Dispensing Nozzles are equipped with a variety of individual dispensing needles.
The needles are arranged according to product-specific geometries. Complex dispensing tasks can be carried in a short time.
Large amounts of material can be applied quickly.
Multiple dispensing nozzles are used for static dispensing tasks i.e. recurring shapes.
Different types of needles with different cross sections can be used for every multiple dispensing nozzle. more...
Double product jig for the soldering of single stranded wires on PCBs.
The wires are guided in grooves and are each fixed and held in position by a clamping device.
The clamping devices can be opened on the touch of a button after the soldering process. more...
UV irradiation field with 10 high power fluorescent tubes, providing optimum homogenous irradiation.
Radiation surface of around 600mm x 600mm.
Best used in applications requiring low UV intensity demand, eg for the curing of glass adhesives in the glass processing industry.
Separate power supply unit for 230V/50Hz or 115V/60Hz.
Universally applicable, simple fixing to the back of the field. more...
Dispensing system for the application of flux before a further Hot Bar Soldering process.
A special nozzle system ensures a consistent application of flux onto the soldering joint.
The dispensing unit moves onto the product.
Easy- to- clean, low-maintenance flux dispensing system for integration into production lines.
All dispensing nozzles are customized products. more...
Deutsch
English
Standard-Systems
